启动按钮start up button

A：双手触发启动（半自动模式）

Trigger start with both hands (semi-automatic mode)

为确保操作者的人身 ，本设备将启动设备设置为双手触发启动模式，在0.3秒时间内双手同时按下启动按钮，压装机自动启动并完成一个工作循环；

In order to ensure the operator's personal safety, the device sets the startup device to the two-hand trigger start mode, and presses the start button simultaneously with both hands within 0.3 seconds, the press machine automatically starts and completes a work cycle;

     B：寸动启动（手动模式）

     进入参数设置窗口，点动“手动下”按钮，压力头向下寸动，点动“手动上”按钮，压力头向上寸动。

B: Inching start (manual mode)

紧急停止  emergency stop

在任何状态下(设置状态除外)作为紧急停止用,在发生紧急情况下,按下急停按钮,设备将处于暂停状态,设备无法进入下一步动作,只有人工逆时针旋转按钮,让按钮释放后才能正常运行

In any state (except the setting state) as an emergency stop, in the event of an emergency, press the emergency stop button, the device will be in the pause state, the device can not enter the next action, only the manual counterclockwise rotation button, let the button release In order to run normally

 

系统启动System startup

   当外部电源接通（总开关闭合）后，点压该按钮，设备控制系统电源接通。长时间不使用该设备时，请务必切断主回路电源开关（断路器总开关）

When the external power is turned on (the main switch is closed),, be sure to turn off the main circuit power switch (circuit breaker main switch)

复位开关   Reset switch

设备在运行过程中若点压此设备，设备将慢速复位至工作原点。

If the device is pressed during operation, the device will be slowly reset to the working origin.

三 色 灯   Three-color light

实时显示设备当前工作状态

Real-time display of the current working status of the device

1. 绿灯闪亮：  工作中
   The green light is shining: at work
2. 黄灯闪亮：  待机中
   Yellow light flashes: Standby
   3. 红灯闪亮： 异常报警
   Red light flashes: abnormal alarm
   蜂 鸣 器  Buzzer
   设备在运行中发生异常情况下，蜂鸣器会发出“哔！哔！哔！”短促的提示音When the device is abnormal during operation, the buzzer will sound “bi! bi! bi!”
    
   USB插槽   USB slot
   将U盘插入USB插槽可导出触摸屏内所有的压装数据。
   Insert the USB flash drive into the USB slot to export all the press-fit data in the touch screen.
      I/O接口（选配）I/O interface (optional)
   与外部设备或夹具装置联机使用
   Online use with external equipment or fixtures
      触 摸 屏   touch screen
   触摸式组态功能显示屏，进行系统和程序参数设置，显示当前设备状态等功能Touch configuration function display, system and program parameter setting, display current device status and other functions

设 备 名 称：BSW08-5000KG系列精密伺服压力机
Equipment name: BSW08-5000KG electronic press

    外 形 尺 寸： 750X755X2000mm(长X宽X高)

Dimensions: 750X755X2000mm (length X width X height)

设 备 重 量： 约900kg

Equipment weight: about 900kg

设 备 功 率： 2.0KW  (Equipment Power: 2.0KW)

工 作 电 压： 单相AC220V，50HZ

Working voltage: single phase AC220V, 50HZ

环 境 温 度： 0—40OC

Environmental temperature: 0-40OC

 大 压 力： 3000kgf        

Maximum pressure: 3000kgf

压力使用范围： 100-5000kgf

Pressure range: 100-5000kgf

压力设定单位： 1Kgf

Pressure setting unit: 1Kgf

 大 行 程：  240mm

Maximum travel: 240mm

位移重复精度：±0.01mm

Displacement repeatability: ±0.01mm

压 装 速 度：  0.1-35mm/s

Pressing speed: 0.1-35mm/s

快 进 速 度：  10-100mm/s

Fast forward speed: 10-100mm/s

保 压 时 间：  0-99S

Pressure holding time: 0-99S

压力重复精度： ±1%

Pressure repeatability: ±1%

 

1. 该设备机体上有 吊装位，请注意设备上部吊装孔位置；
   The device has a specified lifting position on the body, please pay attention to the position of the lifting hole on the upper part of the device;
   2.接通电源前，请检查电源电压以及容量（单相220V±10% ，50Hz，0.75KW）。Before turning on the power, check the power supply voltage and capacity (single phase 220V ± 10%, 50Hz, 0.75KW).
    
    
    
   1. BSW08系列伺服压力机定位后，通过水平尺调节设备工作台面处于水平状态；并进行下列检查：After the BSW08 series electronic press is positioned, the working surface of the equipment is leveled by t vel gauge; and the following checks are performed:
   ※ 尊龙人生就是搏网站连接要合乎尊龙人生就是搏网站安装规范；
   Electrical connections must comply with electrical installation specifications;
    ※ 设备接地保持良好；
   The equipment grounding is kept good;
   ※ 按钮、指示灯功能正常；
   The button and indicator light function normally.
    ※ 设备接通、断开动作可靠；
   The device is connected and disconnected reliably; 
     ※ 紧固件无松动；The fastener is not loose;
   2. 设备准备状态：Equipment preparation status:
   A．顺时针转动旋开紧停按钮；
   Turn clockwise to open the stop button;
   B．将设备侧边的总电源断路器和电箱内的可控制电源开关置于ON状态；
   Put the main power circuit breaker on the side of the equipment and the controllable power switch in the electric box to the ON state;
   C. 点压操作面板上的“系统开启”按钮，接通电源；
   Press the “System On” button on the operation panel to turn on the power;
   D．电源指示灯亮，此时设备即进入工作准备状态；
   The power indicator is on, and the device is ready for work.

 

 

• 每日工作之前和工作之后及时清洁设备工装台；
• Clean the equipment station before and after work every day
• 清洁布请使用干燥软棉布。
• Use a dry soft cotton cloth for the cleaning cloth.
• 保持触摸屏表面清洁，清洁触摸屏时，请关闭设备电源，严禁带电清洁。
• ,.
   
   
   
• 定期清洁机台所有部件。Clean all parts of the machine regularly.
• 定期检查各固定部件间的连接情况；
• Regularly check the connection between each fixed component;

• 各部件间连接应牢固可靠；
• The connection between the components should be firm and reliable;
• 连接螺纹处无松动现象；
• There is no looseness at the connecting thread;

• 定期对非油漆部件表面进行防锈处理。
• Regularly rust-proof the surface of non-painted parts.
• 定期给各运动部件进行润滑除尘。
   
   
   

• 布斯威产品未拆箱时，在装车及卸货过程中务必使用叉车搬运，无明显提示请禁止采用吊装；
• 在使用叉车搬运时，请注意包装箱上的叉位口位置。
• 布斯威产品为精密机械设备，在运输过程中必须妥善固定，严禁倾斜。
• 运输过程中请注意轻放、不可倒置、防潮等注意事项。
   
   
   
   
   
• 布斯威产品在贮存时须注意防潮、防锈、防尘等措施；
  布斯威产品为精密机械设备贮存时不得倾斜或迭加其它物品